Menu
Home
Post Something
Forums
Current Activity
New posts
Search forums
What's new
New posts
Latest activity
News & Features
The Marketplace
Cars for Sale
Engine and Performance
Chassis and Wheels
Exterior and Body
Interior and Cockpit
ICE - In Car Entertainment
Car Shops and Services
Toys and Wares
All Other Stuff
Jobs and Vacancies
Looking For
Members
Log in
Register
What's new
Search
Search
Search titles only
By:
Current Activity
New posts
Search forums
Menu
Log in
Register
Reply to thread
See what others are reading now! Try Forums >
Current Activity
Home
Forums
Main Forums
Car Talk
Forced Induction & Engine Management
Fully utilise Haltech E6X
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="nan83" data-source="post: 3810970" data-attributes="member: 6718"><p>for boost control...</p><p></p><p>do u use trim module + wastgate solenoid</p><p></p><p>or just wastegate solenoid only..</p><p></p><p>trim module connected to trim input ( pin 26 ground , pin 10 trim signal , pin 18 5v supply)</p><p>solenoid connected to pwm output#1 - 4 ...</p><p></p><p>antilag, launch control & flatshift use Aux in (pin 28)</p><p>anti-lag air bypass solenoid ise pwm output#1-#4</p><p></p><p>boost control not using aux in ... so no prob lah...</p><p>________________________________________________</p><p></p><p>for flatshift</p><p></p><p>what do you mean by control mechanicals??</p><p>it not operate like dogbox gear lah... that one no need to press clutch </p><p></p><p>flat shift operating is simple... switch that locate at clutch paddle will tell ecu whan you press the clutch... so ecu retard ignition timing to 15° ATDC, allowing the throttle to be held wide open whilst changing gears. This reduces engine deceleration so gear changes will be quicker, but it also prevents the engine from over-revving when the clutch is disengaged. The driver normally depresses the switch just as they are goingto disengage the clutch and then releases the switch just after the clutch is re-engaged. The driver can therefore keep the throttle wide open throughout the gear change.</p><p></p><p>_______________________________________________</p><p></p><p>normally for pnp hardness, stock sensor that use it coolent temp, cam or crank sensor, o2 sensor, throttle position.... haltech sensor just map & air temp</p><p></p><p>stock sensor not use, maf sensor, knock sensor...</p><p></p><p>just open your halwinx and see yr tuner configure or not o2 close loop funtion...</p><p></p><p>air temp correction map for fuel & ign .... need to check oso.. tuner tune it or not... if not waste of money only buy that sensor... just to take data for log ok lah...</p><p>air temp correction map hard oso to fully tune... need to check fuel & ign at sunny day, night, in rain.... coz the intake temp depend on ambient temperature oso... hi boost oso increase temp...</p><p>normally tuner will just assume the map... agak2 only... not fully tune lah</p><p></p><p>same oso for cold start.... tuner cannot fully tune oso... it take time, to cool back the engine 2-3 times...</p></blockquote><p></p>
[QUOTE="nan83, post: 3810970, member: 6718"] for boost control... do u use trim module + wastgate solenoid or just wastegate solenoid only.. trim module connected to trim input ( pin 26 ground , pin 10 trim signal , pin 18 5v supply) solenoid connected to pwm output#1 - 4 ... antilag, launch control & flatshift use Aux in (pin 28) anti-lag air bypass solenoid ise pwm output#1-#4 boost control not using aux in ... so no prob lah... ________________________________________________ for flatshift what do you mean by control mechanicals?? it not operate like dogbox gear lah... that one no need to press clutch flat shift operating is simple... switch that locate at clutch paddle will tell ecu whan you press the clutch... so ecu retard ignition timing to 15° ATDC, allowing the throttle to be held wide open whilst changing gears. This reduces engine deceleration so gear changes will be quicker, but it also prevents the engine from over-revving when the clutch is disengaged. The driver normally depresses the switch just as they are goingto disengage the clutch and then releases the switch just after the clutch is re-engaged. The driver can therefore keep the throttle wide open throughout the gear change. _______________________________________________ normally for pnp hardness, stock sensor that use it coolent temp, cam or crank sensor, o2 sensor, throttle position.... haltech sensor just map & air temp stock sensor not use, maf sensor, knock sensor... just open your halwinx and see yr tuner configure or not o2 close loop funtion... air temp correction map for fuel & ign .... need to check oso.. tuner tune it or not... if not waste of money only buy that sensor... just to take data for log ok lah... air temp correction map hard oso to fully tune... need to check fuel & ign at sunny day, night, in rain.... coz the intake temp depend on ambient temperature oso... hi boost oso increase temp... normally tuner will just assume the map... agak2 only... not fully tune lah same oso for cold start.... tuner cannot fully tune oso... it take time, to cool back the engine 2-3 times... [/QUOTE]
Insert quotes…
Verification
Post reply
The Marketplace Latest
R35 GTR 2020 Original Rim Wheels
Started by
aycy
Chassis and Wheels
Greddy Trust R35 Y Pipe GTR GTR35 Exhaust Used
Started by
aycy
Exterior and Body
Nissan Silvia S15 Door Trim Card Panel Bride
Started by
aycy
Interior and Cockpit
Atlas Force UHP Used Tire Tyre 275 35 20
Started by
aycy
Chassis and Wheels
R35 GTR Ohlins Adjustable Suspension
Started by
aycy
Chassis and Wheels
Nismo LMGT4 40th Anniversary 18x9.5+12 White
Started by
aycy
Chassis and Wheels
Rays G025 18 inch VW Audi S3 A45 CLA45 Golf MK7 MK8 Rim
Started by
aycy
Chassis and Wheels
S13 S14 S15 Used Drift Rim Tire Set
Started by
aycy
Chassis and Wheels
R35 Used Titanium Exhaust
Started by
aycy
Engine and Performance
PWR FL5 / FK8 Street Radiator 42MM
Started by
aycy
Engine and Performance
Posts refresh every 5 minutes
White Smoke
Hi to all,
My atr already making some fogging..when idle/traffic light can see from mirror.
Just wanna to know what cause that problem..and cost
1. if from valve seal what is symptom? How to know valve seal...
Maxxis tyre shop in KL?
Any shop selling Maxxis tyre here in KL?
planning to get Maxxis MA-Z1 17"
Googled but only found Maxxis dealers for motorcycle tyre
few item want to buy
Pls delete this threads
Recent Posts
Looking for 2.5-16 cosworth halfcut for 190E
Started by
Tuanku.J
Euro
Thrills and Spills at Zhuhai: Porsche Carrera Cup Asia Rounds 3 & 4 Recap
Started by
The_Mechanic
News and Features
Proton Records High Demand for S70 with 1 Unit Booked every 4 minutes
Started by
The_Mechanic
News and Features
Toyota Malaysia Enters Regional GT Racing with TGR Racing Malaysia
Started by
The_Mechanic
News and Features
Home Win and Double Podium for Akash Nandy at Sepang Season Opener
Started by
The_Mechanic
News and Features
Search
Online now
sn964444
Enjoying Zerotohundred?
Log-in
for an ad-less experience
Home
Forums
Main Forums
Car Talk
Forced Induction & Engine Management
Fully utilise Haltech E6X