Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="wirahybrid" data-source="post: 4379737" data-attributes="member: 82932">hi there, i was also planning to do the same type of arc induction box during my sem break.. the type of material that i was planning to use was aluminium(haven't decided on wat size yet). method of doing it:1)first method:i was planning on making a template out of card board first with all the mounting holes indicated then cut the corresponding pieces out of aluminium sort of like a jig saw puzzle, take the pieces to a nearby exhaust shop that does intercooler piping and have them weld it together...2)second method: using the same template, open it up till i get a single flat piece. transfer the template onto a sheet of aluminium and cut it out. i had two ways of putting it together:a)first is the same as the above; have them weld up all the joints..b)other way was to actually to have extended sides(circled in the example pic attached)-not sure what the proper term for it..:stupid: ... drill holes on those extended sides and to its corresponding sides to be attached with and rivet it... then take it to the exhaust shop to have the edges welded for proper seal... then have a 3" hole cut out and an aluminium pipe of desired length welded on.. and mount it at desired positionbt my only question is in the design there seems to be only one hole, so i'll be assuming the hole is connected to the MAF sensor via a short length of flexi hose.. but where will the air be sucked in. i can see a square at the front so i'll be assuming that where the air comes in. just to share with you(hope you dont mind :hmmmm:) my design in mind was to DIY a custom headlight out of fiberglass with a projector lamp on the right side(drivers side headlight; towards the grill side for wira,putra,satri) and a CAI funnel next to it connected directly to the airbox.. the airbox will be placed where the battery was (moved mine to the trunk)... this is just my 2 cents... hope u dont mind me sharing<img src="https://zerotohundred.com/forums/styles/default/xenforo/smilies/biggrin.gif"  class="smilie" loading="lazy" alt=":biggrin:" title="Biggrin    :biggrin:" data-shortname=":biggrin:" /><img src="http://zerotohundred.com/forums/styles/default/xenforo/smilies/burnout.gif"  class="smilie" loading="lazy" alt=":burnout:" title="Burnout    :burnout:" data-shortname=":burnout:" /></blockquote>

Verification

The Marketplace Latest

2019 Toyota FORTUNER 2.4 VRZ 4X4 (A) Diesel
- Started by aycy
- Cars for sale
Advan GT Beyond 19 Civic Type R FK8 FL5 Rim Wheel
- Started by aycy
- Chassis and Wheels
TE37 Saga S Plus 18 Civic Type R FL5 FK8
- Started by aycy
- Chassis and Wheels
Perodua Bezza body kit/spoiler
- Started by jeff6126
- Exterior and Body
Honda Jazz FLRS side skirt
- Started by jeff6126
- Exterior and Body
yellowcaliper /caliperspray
- Started by jeff6126
- Exterior and Body
Te37 Track Edition 2 FK8 FL8 Civic Type R Rim Wheel...
- Started by aycy
- Chassis and Wheels
Revozport R35 GT Wing Spoiler and Trunk
- Started by aycy
- Chassis and Wheels
original rare Work Emotion 11R 18x8.5jj offset +47...
- Started by david tao
- Chassis and Wheels
Spoon FK8 FL5 19 inch rim wheel Type R
- Started by aycy
- Chassis and Wheels

Posts refresh every 5 minutes

Where you go for alignment?

As title, where do you guys (kaki) go to align your wheels?
I have been to some, most of their machines didn't measure correctly.
Any shop (PJ/KL) recommend to do the alignment? :burnout: