Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="Izso" data-source="post: 1064585447" data-attributes="member: 2429">Wheelspin = get LSD. About 1k price range for used. Driveshaft - custom driveshaft or modified one probably 1k price range. Gearbox - don't modify over the capacity of the GB. Close story.VDO is smart enough to handle you in your current financial situation. Once you start venturing into forced induction then it'll be time to consider piggybacks or standalones.Wiser in what sense? There are pros and cons to both scenarios. If transplant, need to consider refurbishing the 4G93T. Engine alone approximately 4k, refurbish and all, probably 1.5k, then installation 1k, JPJ - time and finally puspakom - 100+ and must adhere to all puspakom guidelines otherwise you'll waste a lot of time redoing the inspection.BOT the 4G15 you don't need to do any registration and you'd be familiar with whats good and whats bad about the engine. It's also much easier to work on compared to DOHC. Lesser parts to fail and easier to tune. Personally I'd go with 4G15 and mod that. Cost wise probably will be less cost effective but nothing beats the satisfaction of building your own car rather than borrowing it from another engine that's not yours to begin with. Maybe it's just me and my 6 months DIY overhauling the engine which makes me so sentimental to 4G15 engines.NA will always give the more immediate performance gains but FI will give you the bigger kick in the balls but is more of a handful. NA is less likely to get you in trouble with JPJ roadblocks and NA is helluva easier to mod compared to FI. And the thing is - with NA, you can anytime opt to go FI. Sort of. That's assuming you don't go high compression like I did.</blockquote>

Verification

The Marketplace Latest

Advan GT Beyond 19 Civic Type R FK8 FL5 Rim Wheel
- Started by aycy
- Chassis and Wheels
TE37 Saga S Plus 18 Civic Type R FL5 FK8
- Started by aycy
- Chassis and Wheels
Perodua Bezza body kit/spoiler
- Started by jeff6126
- Exterior and Body
Honda Jazz FLRS side skirt
- Started by jeff6126
- Exterior and Body
yellowcaliper /caliperspray
- Started by jeff6126
- Exterior and Body
Te37 Track Edition 2 FK8 FL8 Civic Type R Rim Wheel...
- Started by aycy
- Chassis and Wheels
Revozport R35 GT Wing Spoiler and Trunk
- Started by aycy
- Chassis and Wheels
original rare Work Emotion 11R 18x8.5jj offset +47...
- Started by david tao
- Chassis and Wheels
Spoon FK8 FL5 19 inch rim wheel Type R
- Started by aycy
- Chassis and Wheels
Litchfield GTR R35 Road Suspension Kit Absorber
- Started by aycy
- Chassis and Wheels

Posts refresh every 5 minutes

Neuton NT8000

Hi guys, Any opinions on Neuton NT8000's? Is there anything to watch out for? Already bought them
(my nexen n7000's failed on me, side wall cracked after almost 4 years with barely 15000km on them) just wanted to...

RCA Track Day, Saturday 5 Sept 09. 1pm - 4pm

Hey everyone..

Next RCA Track Day is Saturday 5 Sept 09 from 1pm till 4pm. Another 3hrs of fun woohoo!!

Price is the same:
- RM 350 for 1 car and 1 driver;
- RM 100 for 2nd driver;
- RM 70 for a transponder...

How to remove front & rear seats on Satria

hi guys,
im just wondering wat are the steps to remove front & rear seats on satria?? izzit hard to do? what are the tools needed? thanks:cool: